地埋示踪线于对相关管道的探测、追踪及定位，一样平常会接纳金属线芯，通过探测装备给金属线施加信号，由探测吸收机吸收信号，从而找到示踪线的准确位置，即同步追踪到管道的详细位置；以便于对管道举行刷新及维修
。下面来讲讲地埋示踪线装置毗连的操作说明内容吧
。

The buried tracer line is used to detect, track and locate the relevant pipeline. Generally, the metal wire core is used to apply signals to the metal wire through the detection equipment, and the detection receiver receives the signals, so as to find the accurate position of the tracer line, that is, synchronously track to the specific position of the pipeline; So as to facilitate the reconstruction and maintenance of the pipeline. Let's talk about the operating instructions for the installation and connection of buried tracer lines.

产品用途：用于埋地塑料管道的探测及示踪
。

Application: used for detecting and tracing buried plastic pipelines.

适用规模：燃气埋地PE管道、供水埋地PE、PVC管道、及非金属埋地管道
。

Scope of application: gas buried PE pipeline, water supply buried PE, PVC pipeline, and non-metallic buried pipeline.

装置零部件及工具

Installation parts and tools

1、所有物品

1. All items

2、毗连夹/防水(腐)毗连器

2. Connecting clip / waterproof (corrosion) connector

3、工具

3. Tools

操作办法：直线毗连

Operation steps: straight line connection

用剪钳剪断示踪线--铰剪剪开两条示踪线--剥去PE外；て--穿入防腐/防水毗连器--金属丝穿入蓝色接线柱内--用夹钳将毗连夹夹紧--确认接口处毗连牢靠--将防腐/防水毗连器紧固

Cut off the trace line with scissors -- cut off two trace lines with scissors -- strip the PE outer protective skin -- thread into the anti-corrosion / waterproof connector -- thread the metal wire into the blue terminal -- clamp the connecting clamp with pliers -- confirm that the connection at the interface is firm -- tighten the anti-corrosion / waterproof connector

操作办法：三通毗连

Operating steps: tee connection

替换成玄色双孔胶头--将三条线穿入防水讨论--金属丝穿入黄色接线柱后夹紧--紧固防腐/防水毗连器

Replace with black double hole rubber head -- thread the three wires into the waterproof connector -- thread the metal wire into the Yellow terminal and clamp it -- tighten the anti-corrosion / waterproof connector

凭证操作说明要求施工：

Construction in accordance with the operating instructions:

1、用铰剪剪开（疏散）两条并联的示踪线时，应注重两条线是否匀称，被脱离的两条示踪线外貌要平滑，不可有凸台、尖角（很是主要），会影响毗连器的防水性能
。

1. When cutting (separating) two parallel trace lines with scissors, pay attention to whether the two lines are uniform. The surface of the separated two trace lines should be smooth without bosses and sharp corners (very important), which will affect the waterproof performance of the connector.

2、是否有金属线漏出，不可将外漏金属丝的示踪线埋地
。

2. Whether there is any metal wire leakage, the tracer line of the leaked metal wire shall not be buried.

3、在剥PE；げ闶辈灰鹕私鹗粝
。

3. Do not damage the metal wire when stripping the PE protective layer.

4、接线柱毗连好讨论后，应用力拉动讨论两头的示踪线，检查讨论的毗连强度
。

4. After the terminal is connected to the joint, the tracer wires at both ends of the joint shall be pulled to check the connection strength of the joint.

5、不要遗忘对防腐/防水毗连器的紧固；出地后的示踪线头部位，应用防水胶布和热缩管封紧
。

5. Do not forget to fasten the anti-corrosion / waterproof connector; After leaving the ground, the tracer thread head shall be sealed with waterproof tape and heat shrinkable pipe.

6、地埋示踪线应在每个阀门井处设置讨论便于检测，每五百米必需设置一个检测井
。

6. The buried tracer line shall be provided with joints at each valve well for inspection, and one inspection well must be provided every 500m.

以上就是问题解答的相关内容了，希望能够资助到各人，如对这一问题还保存任何疑问，都接待关注我们网站并咨询jdb电子事情职员，将竭诚为您效劳
。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website And consult our staff, will serve you wholeheartedly.